ABS filament for heat-resistant parts
Part of the heat-resistant filament guide. ABS is a common step up from PLA and PETG for parts that sit in warm places, such as automotive interior trim and clips or housings near motors and electronics. It needs a heated bed and, per Bambu, an enclosed printer. Nothing here was printed or measured by this site; every value links to its source.
What Bambu says about printing it
| Category | In Bambu's table? | Bambu Lab A1 mini | Bambu Lab A1 | Bambu Lab P1S | Bambu Lab X1 Carbon (X1C) | AMS | AMS lite |
|---|---|---|---|---|---|---|---|
| ABS | Yes | Not Recommended | Not Recommended | Recommended | Recommended | Compatible | Not Recommended |
| ABS-GF | Yes | Not Recommended | Not Recommended | Recommended | Recommended | Compatible | Not Recommended |
| ABS-CF | No (derived, see note) | Not rated (Bambu recommends an enclosed printer) | Not rated (Bambu recommends an enclosed printer) | Recommended (Bambu printer-requirements table) | Recommended (Bambu printer-requirements table) | Not rated by Bambu | Not rated by Bambu |
- ABS-CF: Not a row in Bambu's compatibility table. Bambu's printer-requirements table groups ABS, ASA, PC, PA "and their CF/GF reinforced materials" under enclosed printers, and its nozzle guidance requires a hardened steel nozzle for CF/GF materials. (source)
| Material group | Hardened steel nozzle | Nozzle temp (°C) | Bed temp (°C) | Drying before use |
|---|---|---|---|---|
| ABS | Not required | 240–280 | 90–100 | Recommended: 80 °C for 8 h (oven) |
Heat-resistance values from manufacturer datasheets
Sorted by HDT at 0.45 MPa. A dash means the datasheet does not give that value (or gives it without a stated load), so it is left blank rather than estimated. HDT is a lab comparison value measured on test bars under a fixed load, not a rated service temperature, and depends on test method, print orientation and annealing. Retrieved .
| Brand | Product | HDT 0.45 MPa (°C) | HDT 1.8 MPa (°C) | Tg (°C) | Vicat (°C) | HDT method | Notes | Source |
|---|---|---|---|---|---|---|---|---|
| Polymaker | PolyLite ABS | 100 | 98 | 101 | 104 | ISO 75 | — | TDS |
| Bambu Lab | ABS-GF | 99 | 88 | — | 103 | ISO 75 | TDS: specimens annealed and dried at 80 °C for 12 h before testing. TDS lists Tg as N/A. | TDS |
| Sunlu | ABS | 95 | — | 109 | 86 | ISO 75 (X-Y) | TDS gives ±5 °C on HDT; no 1.8 MPa value. | TDS |
| Sunlu | High Speed ABS | 93 | — | 105 | 80 | ISO 75 (X-Y) | No 1.8 MPa value. | TDS |
| Sunlu | ABS-FR | 90.5 | — | — | — | ISO 75 (X-Y) | TDS gives ±3 °C; Tg and Vicat listed as "/". | TDS |
| Bambu Lab | ABS | 87 | 84 | — | 94 | ISO 75 | TDS: specimens annealed and dried at 80 °C for 12 h before testing. TDS lists Tg as N/A. | TDS |
| Extrudr | DuraPro ABS | — | — | — | 92 | — | TDS gives "HDT/B ASTM D648 85 °C" without stating the load, so it is not assigned to a load column here. | TDS |
| Overture | ABS | — | — | — | 103.4 | — | TDS lists Vicat only; no HDT or Tg. | TDS |
ABS products in the database
Products with enough sourced data for a page, datasheet heat values first. Enclosure and nozzle columns come from the product's Bambu category plus the database's abrasive and fibre tags; open a product page for the basis of each.
| Product | Brand | Category | Enclosure | Hardened nozzle | HDT 0.45 MPa (°C) | Nozzle °C (min–max) |
|---|---|---|---|---|---|---|
| Bambu Lab ABS | Bambu Lab | ABS | Enclosure recommended | Not required | 87 | 240–270 |
| Bambu Lab ABS-GF | Bambu Lab | ABS-GF | Enclosure recommended | Required | 99 | 240–280 |
| extrudr DuraPro ABS | extrudr | ABS | Enclosure recommended | Not required | — | 230–260 |
| Overture ABS | Overture | ABS | Enclosure recommended | Not required | — | 245–265 |
| Polymaker Polylite ABS | Polymaker | ABS | Enclosure recommended | Not required | 100 | 245–265 |
| SUNLU ABS | SUNLU | ABS | Enclosure recommended | Not required | 95 | 250–290 |
| SUNLU ABS-FR | SUNLU | ABS | Enclosure recommended | Not required | 90.5 | 240–260 |
| SUNLU High Speed ABS | SUNLU | ABS | Enclosure recommended | Not required | 93 | 260–290 |
| SUNLU PC-ABS | SUNLU | ABS | Enclosure recommended | Not required | 102 | 260–280 |
| 3D Fuel Pro ABS | 3D Fuel | ABS | Enclosure recommended | Required | — | 230–260 |
| 3DE Pirate Black | 3DE | ABS | Enclosure recommended | Not required | — | 240–270 |
| 3DJAKE ABS | 3DJAKE | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DPower ABS | 3DPower | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS | 3DXTech | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS 3DXMax | 3DXTech | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS 3DXStat ESD | 3DXTech | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS 3DXTech | 3DXTech | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS CF | 3DXTech | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| 3DXTech ABS GF | 3DXTech | ABS-GF | Enclosure recommended | Required | — | 230–260 |
| Add-North ABS | Add-North | ABS | Enclosure recommended | Not required | — | 230–260 |
| Add-North rABS | Add-North | ABS | Enclosure recommended | Not required | — | ––– |
| Ambrosia ABS Matte | Ambrosia | ABS | Enclosure recommended | Not required | — | 230–265 |
| Ambrosia Über ABS | Ambrosia | ABS | Enclosure recommended | Not required | — | 225–250 |
| Anycubic ABS | Anycubic | ABS | Enclosure recommended | Not required | — | 240–280 |
| Atomic Filament ABS | Atomic Filament | ABS | Enclosure recommended | Not required | — | 230–260 |
| Atomic Filament ABS CF | Atomic Filament | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| AURAPOL ABS | AURAPOL | ABS | Enclosure recommended | Not required | — | 230–260 |
| AzureFilm ABS Plus | AzureFilm | ABS | Enclosure recommended | Not required | — | 250–250 |
| AzureFilm ABS Prime | AzureFilm | ABS | Enclosure recommended | Not required | — | 250–250 |
| Buddy3D ABS | Buddy3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Buddy3D Matte ABS | Buddy3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| CC3D ABS | CC3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| COEX 3D ABS | COEX 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Cookiecad ABS | Cookiecad | ABS | Enclosure recommended | Not required | — | 230–260 |
| Creality ABS | Creality | ABS | Enclosure recommended | Not required | — | 230–260 |
| Creality Hyper ABS | Creality | ABS | Enclosure recommended | Not required | — | ––– |
| Devil Design ABS | Devil Design | ABS | Enclosure recommended | Not required | — | 230–260 |
| ELEGOO ABS | ELEGOO | ABS | Enclosure recommended | Not required | — | 240–280 |
| Eolas Prints ABS | Eolas Prints | ABS | Enclosure recommended | Not required | — | 230–260 |
| Eryone ABS | Eryone | ABS | Enclosure recommended | Not required | — | 230–270 |
| Eryone ABS High-Speed | Eryone | ABS | Enclosure recommended | Not required | — | 240–290 |
| Eryone ABS-CF | Eryone | ABS-CF | Enclosure recommended | Required | — | 240–280 |
| Eryone ABS-GF | Eryone | ABS-GF | Enclosure recommended | Required | — | 240–280 |
| Eryone ABS-PC | Eryone | ABS | Enclosure recommended | Not required | — | 240–260 |
| Eryone ABS+ | Eryone | ABS | Enclosure recommended | Not required | — | 230–260 |
| eSUN 3D ABS+ | eSUN 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| eSUN 3D ABS+CF | eSUN 3D | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| eSUN 3D ABS+HS | eSUN 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Fiberlogy ABS | Fiberlogy | ABS | Enclosure recommended | Not required | — | 230–260 |
| Fiberlogy R ABS | Fiberlogy | ABS | Enclosure recommended | Not required | — | 250–265 |
| Fiberlogy Refill ABS | Fiberlogy | ABS | Enclosure recommended | Not required | — | 250–265 |
| Fiberlogy Refill R ABS | Fiberlogy | ABS | Enclosure recommended | Not required | — | 250–265 |
| FilamentPM ABS | FilamentPM | ABS | Enclosure recommended | Not required | — | 230–260 |
| Filamentworld ABS | Filamentworld | ABS | Enclosure recommended | Not required | — | 230–260 |
| Filatech ABS | Filatech | ABS | Enclosure recommended | Not required | — | 230–260 |
| FLASHFORGE ABS | FLASHFORGE | ABS | Enclosure recommended | Not required | — | 230–260 |
| FLASHFORGE D Series ABS | FLASHFORGE | ABS | Enclosure recommended | Not required | — | 230–260 |
| FormFutura ABSpro | FormFutura | ABS | Enclosure recommended | Not required | — | 230–255 |
| FormFutura ABSpro Flame Retardant | FormFutura | ABS | Enclosure recommended | Not required | — | 240–265 |
| FormFutura EasyFil ABS | FormFutura | ABS | Enclosure recommended | Not required | — | 230–260 |
| FormFutura EasyFil ABS - Glow in the Dark | FormFutura | ABS | Enclosure recommended | Required | — | 230–255 |
| FormFutura Premium ABS Medical | FormFutura | ABS | Enclosure recommended | Not required | — | 235–260 |
| FormFutura ReForm - rTitan | FormFutura | ABS | Enclosure recommended | Not required | — | 245–265 |
| FormFutura TitanX | FormFutura | ABS | Enclosure recommended | Not required | — | 245–270 |
| Francofil ABS | Francofil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Geeetech ABS+ | Geeetech | ABS | Enclosure recommended | Not required | — | 220–250 |
| Geeetech Upgrade ABS | Geeetech | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks ABS CF | Gizmo Dorks | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| Gizmo Dorks Color Change ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks Fluorescent ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks Glow ABS | Gizmo Dorks | ABS | Enclosure recommended | Required | — | 230–260 |
| Gizmo Dorks Low Odor ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks Thermochromic ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| GST3D ABS | GST3D | ABS | Enclosure recommended | Not required | — | ––– |
| Hatchbox ABS | Hatchbox | ABS | Enclosure recommended | Not required | — | 210–240 |
| Hatchbox Glow ABS | Hatchbox | ABS | Enclosure recommended | Required | — | 210–240 |
| IC3D ABS | IC3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| IEMAI ABS | IEMAI | ABS | Enclosure recommended | Not required | — | 220–260 |
| IEMAI CF-ABS | IEMAI | ABS-CF | Enclosure recommended | Required | — | 220–260 |
| IEMAI ESD-ABS | IEMAI | ABS | Enclosure recommended | Not required | — | 230–260 |
| Inland ABS | Inland | ABS | Enclosure recommended | Not required | — | 230–260 |
| Inland Glow ABS | Inland | ABS | Enclosure recommended | Required | — | 230–260 |
| Inslogic ABS FR V0 | Inslogic | ABS | Enclosure recommended | Not required | — | 230–260 |
| Inslogic ABS GF10 | Inslogic | ABS-GF | Enclosure recommended | Required | — | 240–270 |
| kexcelled The K5 ABS T | kexcelled | ABS | Enclosure recommended | Not required | — | 250–290 |
| Kingroon ABS | Kingroon | ABS | Enclosure recommended | Not required | — | 230–260 |
| LDO ABS | LDO | ABS | Enclosure recommended | Not required | — | 250–270 |
| MatterHackers ABS | MatterHackers | ABS | Enclosure recommended | Not required | — | 230–260 |
| Mosaic ABS | Mosaic | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nebula ABS Art Glowing | Nebula | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nebula ABS Art Marble Gray | Nebula | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nebula ABS Art Thermo | Nebula | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nebula ABS Tech 702 | Nebula | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil Glow ABS | Nobufil | ABS | Enclosure recommended | Required | — | 230–260 |
| Nobufil X Astro ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil X Candy ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil X Industrial ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil X Matt Matte ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil X Neon ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Overture Glow ABS | Overture | ABS | Enclosure recommended | Required | — | 245–265 |
| Paramount 3D ABS | Paramount 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Paramount 3D ABS CF | Paramount 3D | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| PolyLite ABS | PolyLite | ABS | Enclosure recommended | Not required | — | 245–265 |
| Polymaker Metallic Polylite Silk ABS | Polymaker | ABS | Enclosure recommended | Not required | — | 230–260 |
| PrimaCreator Primaselect ABS | PrimaCreator | ABS | Enclosure recommended | Not required | — | 220–250 |
| PrimaCreator Primaselect Glow ABS | PrimaCreator | ABS | Enclosure recommended | Required | — | 230–260 |
| PrimaCreator Primavalue ABS | PrimaCreator | ABS | Enclosure recommended | Not required | — | 240–270 |
| PrimaSelect ABS | PrimaSelect | ABS | Enclosure recommended | Not required | — | 220–250 |
| PrimaValue ABS | PrimaValue | ABS | Enclosure recommended | Not required | — | 240–270 |
| Print With Smile ABS | Print With Smile | ABS | Enclosure recommended | Not required | — | 230–260 |
| PrintedSolid ABS CF | PrintedSolid | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| Push Plastic ABS | Push Plastic | ABS | Enclosure recommended | Not required | — | 230–260 |
| Push Plastic CF ABS | Push Plastic | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| Push Plastic Matte ABS | Push Plastic | ABS | Enclosure recommended | Not required | — | 230–260 |
| QIDI Tech ABS Metal Rapido | QIDI Tech | ABS | Enclosure recommended | Not required | — | 220–250 |
| QIDI Tech ABS Rapido | QIDI Tech | ABS | Enclosure recommended | Not required | — | 240–280 |
| QIDI Tech ABS-GF25 | QIDI Tech | ABS-GF | Enclosure recommended | Required | — | 240–280 |
| QIDI Tech Odorless ABS Rapido | QIDI Tech | ABS | Enclosure recommended | Not required | — | 240–280 |
| ROSA3D Filaments ABS V0 FR | ROSA3D Filaments | ABS | Enclosure recommended | Not required | — | 230–260 |
| ROSA3D Filaments Matte ABS | ROSA3D Filaments | ABS | Enclosure recommended | Not required | — | 230–260 |
| RS PRO ABS | RS PRO | ABS | Enclosure recommended | Not required | — | 230–270 |
| SainSmart ABS | SainSmart | ABS | Enclosure recommended | Not required | — | 230–260 |
| Sakata 3D ABS | Sakata 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Siraya Tech Fibreheart ABS HT HF | Siraya Tech | ABS | Enclosure recommended | Not required | — | 240–260 |
| Siraya Tech Fibreheart ABS-CF Core | Siraya Tech | ABS-CF | Enclosure recommended | Required | — | 250–280 |
| Siraya Tech Fibreheart ABS-GF | Siraya Tech | ABS-GF | Enclosure recommended | Required | — | 250–270 |
| SMART MATERIALS 3D ABS | SMART MATERIALS 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Snapmaker ABS | Snapmaker | ABS | Enclosure recommended | Not required | — | 240–280 |
| SOVB 3D Fil ABS | SOVB 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| SOVB 3D Glow ABS | SOVB 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Spectrum ABS | Spectrum | ABS | Enclosure recommended | Not required | — | 230–260 |
| Spectrum ABS FR V0 | Spectrum | ABS | Enclosure recommended | Not required | — | 240–265 |
| Spectrum ABS GP450 | Spectrum | ABS | Enclosure recommended | Not required | — | 235–255 |
| Spectrum ABS Kevlar | Spectrum | ABS | Enclosure recommended | Required | — | 250–270 |
| Spectrum ABS Medical | Spectrum | ABS | Enclosure recommended | Not required | — | 235–255 |
| Spectrum smart ABS | Spectrum | ABS | Enclosure recommended | Not required | — | 230–255 |
| Tectonic 3D Aura ABS | Tectonic 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| TEQStone ABS | TEQStone | ABS | Enclosure recommended | Not required | — | 210–250 |
| TINMORRY ABS Pro | TINMORRY | ABS | Enclosure recommended | Not required | — | 220–260 |
| Verbatim ABS | Verbatim | ABS | Enclosure recommended | Not required | — | 230–260 |
| Winkle ABS | Winkle | ABS | Enclosure recommended | Not required | — | 230–260 |
More
- All ABS filaments (full spec tables)
- ASA filament for heat-resistant and outdoor parts
- Polycarbonate (PC) filament for heat-resistant parts
- Nylon (PA6, PA12) filament for heat-resistant parts
- Carbon-fiber-filled filament for heat-resistant parts
Shop Elegoo ABS filament (affiliate link)
Affiliate disclosure: this is an affiliate link. If you buy through it we may earn a commission at no extra cost to you. It doesn't change which data we show. The link goes to Elegoo's own store, not to a specific product listed on this page.